Sears 113.24611 Uživatelský manuál

ownersmanualMODEL NO. 113.24611CAUTION:Read GENERAL and ADDITIONAL SAFETY INSTRUCTIONS carefullyCRAFTSMANCOMMERCIAL 15-1/2 INCH DRILL PRESSassembly op

assemblyNOTE: When using motors which have 1/2 in. die. shafts, place the adapter sleeve (furnished with the motor) on the shaft so tha

5, Remove the belt guard by "pushing in" on the two "links”.6. Place motor on drill press . . . screw the pivot screws into the holes

assemblyINSTALLING AND TENSIONING BELT1. Place a straightedge such as a piece of wood, metal or framing square across the pulleys.2. Move the motor

getting to know your dril! pressQUILL- SPLINES (GROOVES)SPINDLERACK(TEETH)CHUCKQUILL AND SPINDLE ASSEMBLY INSIDE OF DRILL PRESS11 "ON-OFFSV.&apos

getting to know your drill pressTo turn drill ON . .Insert finger under switch lever and pull.TO turn drill OFF . ., Push lever in.In an emergency;

13 The DEPTH POINTER is locked in place with the THUMBSCREW.14 FEED STOP NUT limits the downward movement of the quill at any des

basic drill press operationINSTALLING DRILLSinsert driil into chuck far enough to obtain maximum GRIPPING of the CHUCK JAWS ... the jaw

adiüsfmerifsWARNilMG: FOR YOUR OWN SAFETY TURN SWITCH "OFF" AND REMOVE PLUG FROM POWER SOURCE OUTLET BEFORE MAKING ANY ADJUSTMEN

adjustments5. LOOSEN all three screws "C", "D", and "E" four turns using 1/4 in. setscrew wrench.NOTE: TIGHTENING BOT

POWER TOOL GUARAWTEECraftsman power tools (or welders) are unconditionally guaranteed, for one year, to give complete satisfaction or the tool will be

ь»офS.-иÛт

PARTS LIST FOR CRAFTSMAN DRILL PRESS MODEL NO. 113.24611Always order by Part Number — not by Key NumberFIGURE 1 PA RTS LISTKey PartKeyPartNo. No.Descr

PARTS LIST FOR CRAFTSMAN COMMERCIAL DRILL PRESS MODEL No. 113.24611Figure 2(DVQQ-«?mFIGURE 2 PARTS LISTKeyNo.PartNo.Description160049‘Screw, Type 23,

PARTS LIST FOR CRAFTSMAN COMMERCIAL DRILL PRESS MODEL No. 113.24611figure 3 " 71158 SPINDLE ASM. STOP PARTS LISTKeyNo.PartNo.Description_71158Spi

SearsownersmanualSERVICEMODEL NO. 113.24611HOW TO ORDER REPAIR PARTSCOMMERCIAL15-1/2 INCH DRILL PRESSNow that you have purchased your drill pre

additional safety instructions for drill pressesWARNING: FOR YOUR OWN SAFETY, DO NOT Never perform- any operation “free-hand"ATTEMPT.TO OPERATE

additional safety instructions for drill presses11. Note and Follow the Safety Rules that Appear on the Panel on the Left Side of the Head:DANGER: FO

motor specifications and electrical requirementsMOTOR SPECIFICATIONSThis drill press is designed to use a 1725 RPM motor only. Do not use a

assemblyWARNING; FOR YOUR OWN SAFETY, NEVER CONNECT PLUG TO POWER SOURCE OUTLET UNTIL ALL ASSEMBLY STEPS ARE COMPLETED.1. Unwind the power

2. Apply a light film of oil such as Sears household oil to the spindle nose.3. Place the chuck on the spindle nose and screw the locking collar up

assemblyFEED STOP ROD2.3.INSTALLING THE DEPTH STOP1. Screw the THUMB SCREW partways into the DEPTH POINTER.Place the DEPTH POINTER SHOE inside the po

9. Gently push down on the FEED HANDLES until thehead raises upwards as far as it will go.DO NOT RELEASE FEED HANDLE.10. TIGHTEN THE HEAD LOCK HANDLE