Sears C944.414460 Manuál s instrukcemi

Sears Canada, Inc., Toronto, Ontario M5B 2B846cc/2.8 cu.in. 2-CycleGASOLINE CHAIN SAWWARNING:Read and follow all Safety Rules and OperatingInstruction

10Starting could require many pulls de-pending on how badly the unit isflooded. If engine still fails to start, referto theTROUBLESHOOTING T ABLEorcon

11SThe chain saw operator should keepon the uphi ll side of the terrain as thetree is likely to roll or slide downhillafter it is felled.SStudy the na

12IMPORTANT POINTSSCut only one log at a time.SCut shattered wood very carefully;sharp pieces of wood could be flungtoward operator.SUse a sawhorse to

131stCut2ndCutLIMBING AND PRUNINGW ARNING:Be alert for andguard against kickback. Do not allowthe moving chain to contact any otherbranches or objects

14MAINTENANCEFill in dates as you completeregular serviceCheck for damaged/worn partsCheck for loose fasteners/partsCheck chain tensionCheck chain sha

151. Use the screwdriver end of thechain adjustment tool (bar tool) tomove chain around guide bar toensure kinks do not exist. Thechain should rotate

16LUBRICATIONBar OilFill CapSSeeGUIDE BAR AND CHAIN OILun-der theOPERATIONsection.INSPECT AND CLEAN UNITAND DECALSSAfter each use, inspect complete un

17Outlet CoverExhaust OutletsExhaust Outlets must facechain brake (bar side) of chain saw9. Inspect the muffler gasket and re-place if damaged.10. Rei

18Adjustment located on Chain BrakeInside view ofChain Brake5. Turn adjusting screw by handcounterclockwise until adjusting pinjust touches the stop.6

19STORAGEW ARNING:Perform the followingsteps after each use:SAllow the engine to cool, and securethe unit before storing or t ransporting.SStore chain

2TABLE OF CONTENTSWarranty Statement 2Identification of S ymbols 2Safety Rules 3Assembly 7Operation 7Maintenance 14Service and Adjustments 17Storage 1

20TROUBLESHOOTING TABLETROUBLE CAUSE REMEDYEngine will notstart or will runonly a fewseconds afterstarting.1. ON/STOP switch inSTOP position.2. Engine

21TROUBLESHOOTING TABLE -- ContinuedTROUBLE CAUSE REMEDYChain moves atidle speed.1. Idle speed requiresadjustment.2. Clutch requires repair.1. See “Ca

22U. S. EPA / ENVIRONMENT CANADAEMISSION CONTROL WARRANTY STATEMENTYOUR W A RRA NTY RIG HTS AND OB-LIGATIONS: The U. S . EnvironmentalProtection Agenc

23be provided at all Sears Canada servicecentres. Call 1-800-469-4663. MAINTE-NANCE, REPLACEMENT AND RE-PAIR OF EMISSION RELA TEDPARTS: Any Sears Cana

3SAFETY RULESW ARNING:Always disconnectspark plug wire when making repairs ex-cept for carburetor adjustments. Be-cause a chain saw is a high-speedwoo

4SKeep unit sharp and clean for betterand safer performance.SFollow instructions for lubricating andchanging accessories.SCheck for damaged parts. Bef

5increase the chance of kickback.Follow manufacturer’s chain sharp-ening and maintenance instructions.Check tension at regular intervals,but never wi

6Low-Kickback ChainContoured Depth GaugeElongated Guard LinkDeflects KickbackForce And AllowsWood To GraduallyRide Into CutterCHAIN BRAKE & CKA AN

7locale where such regulations exist, youare legally responsible for maintainingthe operating condition of these parts.Failuretodosoisaviolationofthel

8ON/STOP SWITCHTheON/ST OP SWITCHis used to stopthe engi ne.THROTTLE TRIGGERTheTHROTTLE TRIGGERcontrols en-gine speed.THROTTLE LOCK--OUTTheTHROTTLE LO

9Never use engine or carburetor clean-er products in the fuel tank or perma-nent damage may occur.See theSTORAGEsection for addition-al information.CH