Sears 358.79828 Uživatelský manuál stáhnout pdf (Strana 8)

ASSEMBLY

CUTTING LINE HEAD

CONFIGURATION

Brush and Saw Blade ConflguraUonsfollowthis section.

WARNING:

THE LINE LIMITER IS SHARP AND CAN

CUT YOU. BE SURE TO WEAR GLOVES

WHILE WORKING WITH THE LINE UMITER.

THE PLASTIC UNE TRIMMER SHIELD

MUST BE PROPERLY INSTALLED FOR ALL

LINE TRIMMER USAGE. THE PLASTIC

UNE TRIMMER SHIELD PROVIDES PAR-

TIAL PROTECTION FROM THE RISK OF

THROWN OBJECTS TO THE OPERATOR

AND OTHERS,

INSTALLING UNE :LIMI3_R_-ONTO PI.:ASTIC_?,__;_

LINE TRIMMER SHIELD (See Fig.4)

• Pos_on line limiteronto the plastic line trimmershield.

IMPORTANT: ALTHOUGH SCREW HOLES EXIST ON

BOTH EDGES OF THE PLASTIC LINE TRIMMER

SHIELD, MAKE SURE YOU INSTALL THE LINE UMo

rrER ON THE SIDE SHOWN IN THE ILLUSTRATION.

• Secure line limiterto the plastic line trimmershieldusing

the two mounting screws, lock washers, and nutsfound

in the loose parts bag using a phillips screwdriver and

8ram wrench.

• Tighten securely.

Nuts_ Une Umiter .

--,-,,,,.. / _'___,_, Line Limiter parts are

' ,,,=_,,_'"::_':rs_ located in a bag at-

"///'_ tashed to the Plastic

._-- _l Line Trimmer Shield.

Plastic Line _ \y_-_- Screws

FdmmerShield

Figure 4

PRE-INSTALLATION

If the metal blade shield is installed on the unit,you must

first remove the-nut,supportflange, blade, andmetalb/ade

shield as follows before installing the plastic fine trimmer

shieldand duat line cutdng head.

• Clip blade transport/storage cover over the blade.

(Refer to figure 9)

• Toremove blade (Sea Figures 11or 14), placelockingpin

throughthe gearboxand driving diskto preventthe arbor

shaft from turning and remove the blade nut by turning

clockwise with blade nut/spark plugwrench. Save parts

removed for future use.

• Remove 4 screws with hex key holding the metal blade

shield. Save these 4 screws for installationofthe plastic

line trimmer shield.

INSTALLING THE PLASTIC LINE TRIMMER

SHIELD (See Fig. 5 )

• Place the plastic line trimmershieldon the gearbox, and

align the four screw holes as illustmfed.

• Place the shield support plate under the shield and

align the four screw holes.

• Secure the plasticline trimmershieldusing the 4 mount-

ing screws provided in the loose parts bag.

• Tighten evenly (70 Ib-in mimimum) using the hex key

provided in the loose parts bag.

Arbor _ -F_

Driyin_] /t!/i_ _J_ Plast_Une

.....Di 2! . / T,mme,.

- Shield

Shield Support __,, _.

Plate

Figure 5

INSTALLING THE DUAL MNE HEAD

(See Fig. 6 & 7 )

Before installing the dual line head, make sure the driving

diskis in place on the gear box,

• Rotate the hex fastener on the dual line head counter-

clockwise onto the arbor shaft.

•Tum the arbor shaftto align one of the three holes inthe

ddving diskw_ththe hole in the gearbox.

• Insert the locking pin through the gearbox and driving

disk. This will lock the drivingdisk, and prevent the arbor

shaft from turning while you tighten the dual line head.

• While holdingthe Iockingpinin place, tightenthe dual line

head onto the arbor shaft counterclockwise using the

blade nut/spark plug wrench(15-20 Ib-ft);

Should the arbor shaft continue to turnwhile you are tight-

eningthe dualline head, re-positionthe/ockingpinthrough., ,,..

the gearbox and drivingdisk.

Locking Pin ArborShaft

......Plastic Line

Trimmer Shield Disk

Dual Hex Fastener

(underneath)

Figure 6

Lockin! Pir_ual Cutting Head

Plastic Line

Trimmer Shield _'< II Counterclockwis_

Blade Nut/Sl_ irk Plug

Remove Clockwis_

Wrench

Figure 7

-8-

1 2 3 4 5 6 7 8 9 10 11 12 13 ... 32 33

Komentáře k této Příručce

Žádné komentáře

Sears 358.79828 Uživatelský manuál Strana 8

Komentáře k této Příručce

Související produkty a manuály pro Zahradní nářadí Sears 358.79828